Dixon 560 Manuel d'utilisateur

SEAT ASSEMBLY INSTRUCTIONS 1. Place seat back against frame of seat bottom. Align top & bottom holes in frame with the t-nuts in seat back. Inse

12. Install all-thread hex head bolts into seat straps. Place (1) 5/16-18 x 3" bolt through hole located 1-5/8" from end of strap. Place (

UPPER CONTROL LEVER INSTALLATION 1. Raise rear body cover to fully open position. 2. Install flat washer on right hand swivel plate weldment. Next

MOWER DECK INSTALLATION NOTE: Brake link (P/N 5283) normally used for installation of engine to mower deck drive belt, has been placed in position du

MOWER DECK LEVELING PROCEDURE LEVELING PRINCIPALS: A. There are a total of (4) threaded adjusters which will control the attitude or pitch of th

FINAL PREPARATION MOWER DECK DEFLECTOR: Remove hair pin cotter (P/N 3072) from deflector pin (P/N 6297), remove pin. Position deflector (P/N 8799) on

OPERATION INSTRUCTIONS The safe and successful operation of the Model 560 will depend upon the operator having the correct knowledge of all controls

OPERATION INSTRUCTIONS: (Continued) BRAKING: To brake mower, move both levers in direction opposite of travel, release levers to neutral, set par

CARE AND MAINTENANCE - MODEL 560 This portion of the Model 560 owners manual deals with normal service items which can be performed by the owner. Ple

PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENT Dixon has used two types of electric clutches. One type is the Borg Warner and the second one is the Ogura. E

IMPORTANT - READ CAREFULLY The Dixon ZTR Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is

CARE AND MAINTENANCE - MODEL 560 MOWER DECK SERVICE CUTTER BLADE REMOVAL - BELT TENSION: "CAUTION" The removal of the cutter blades for eit

CARE AND MAINTENANCE - MODEL 560 DRIVE SYSTEM ADJUSTMENTS: Adjustment of the drive system is limited to the actual function of the hydrostatic transm

ADJUSTMENT POINTS FOR T-BOX BELT TENSION

FORWARD LEVER STOP ADJUSTMENT Page 20

CARE AND MAINTENANCE - MODEL 560 LUBRICATION: CHASSIS AND MOWER DECK: Number of grease zerks used: (7) LOCATIONS: (1) each front wheel caster, front

CARE AND MAINTENANCE - MODEL 560 CLEANING THE MOWER: A clean machine is a source of pride to the owner. However, cleaning by use of high pressure com

TROUBLESHOOTING MOWER CUT QUALITY: There are many variables that can effect the cut quality of any multi-blade mower. Type and conditions of grass, c

DRIVE SYSTEM: TROUBLESHOOTING SITUATION CAUSES REMEDY Mower pulls to one side or the other Drive adjustment Adjust per operators manual Consult you

TROUBLESHOOTING ELECTRICAL SYSTEM: SITUATION CAUSES REMEDY Starter will not turn engine over Circuit breaker engaged Push button to reset Consult

INDEX 1. SAFETY ...Pages 1- 3 2. WARRANTY POLICY...

ZTR 560 PARTS LIST 1384 Tank Mount Bracket (Short) 3093 5/16"-18 UNC X 1" HH Bolt GR5 1385 Tank Mount Bracket (Long) 3105 1/4" x 1

ZTR 560 PARTS LIST 3297 1/2"-13Thin Profile Nylok 3600 Rebound Mount 3298 Washer .51 5 X. 874 X. 031 3601 Load Mount 3300 Foam Pad 3602 Spac

ZTR 560 PARTS LIST 3955 Clutch Spacer 5554 Spacer 1/2" ODX 1/4" 4124 Solenoid w/Hardware 5558 Hose Fitting 4197 Ignition Switch 5559

ZTR 560 PARTS LIST 8387 Wiring Kit 9171 Spacer 1 .75 8404 Clutch Kit 9172 Spacer 1 .50 8429 Oil Valve/Hose Assembly 9174 Brake Rod 8432 Axle Ho

SAFETY RIDING LAWNMOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY The following examples are the most common causes of injury to the operato

NOTES Page 37

NOTES Page 38

DIXON INDUSTRIES, INC A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 COFFEYVILLE KS 67337 O945 316 251 2OOO FAX 316 251 4117

SAFETY SAFETY REMINDERS: READ CAREFULLY BEFORE OPERATION 1. Wear appropriate, safe clothing when mowing - close fitting jeans or slacks and heavy le

SAFETY REMINDERS: (Continued) 14. Never lift lawnmower by the body, lift only by the frame. 15. Never carry passengers. 16. Use care when pulling

DIXON LIMITED WARRANTY POLICY -- HYDRO-GEAR MODELS This warranty policy applies to all Hydro-Gear mowers or any 50" model, purchased on or after

SPECIFICATIONS CHASSIS: 11 GA - rectangular tube. BODY: Two piece - made of rotational molded polyethylene. Front body contains access panels for bat

SET UP AND SERVICE 1. Seat Assembly Instructions 2. Upper Control Lever Installation 3. Mower Deck Installation 4. Deck Leveling 5. Final Prepara